· Autopilot control / telemetry
· HD Video downlink bandwidth for multiple cameras
· Manual control of aircraft and payloads
· 5+ mile range
We are proud to present Picoradio MIMO NX, a next generation smart broadband IP radio which takes the Picoradio platform to a new level. Based on the Microhard pMDDL, this is available with:
- 900 MHz ISM 2×2 MIMO radio
- tri-band 1.2 / 1.6 / 2.0 GHz 2×2 MIMO L-band radio
- quad-band 1.6 / 1.8 / 2.0 / 2.2 GHz 2×2 MIMO radio
- hexa-band 2×2 MIMO radio:
- 1625 to 1725 MHz
- 1780 to 1850 MHz
- 2015 to 2110 MHz
- 2200 to 2300 MHz
- 2300 to 2390 MHz
- 2402 to 2478 MHz
- dual-band 5.0-5.9 GHz/ 2.4 GHz MIMO radio (coming soon)
All these radios are capable of transmitting broadband data rates (10-20 Mbps+), and simultaneous command and control.
Featuring an onboard user-accessible processor capable of ethernet / prioritized serial / CAN bus communications, switchable USB slave, onboard temperature sensing, fan control, additional ethernet interface, and onboard switchable manual control / SBUS in and out features.
Size: 40x75x10mm
Weight: 25g
The board includes robust connectors, three ethernet ports, and a transparent serial port . The board also has an advanced wide input range power system capable of operating from lithium battery power, aircraft, or Power Over Ethernet voltage ranges as well as an auxiliary power output to provide regulated power for other devices. Bandwidth of up to 21 Mbps is possible. Advanced features such as mesh networking and relay modes are also available.
· Wide range power input: 5-58V
· Up to 1W COFDM RF output, 2×2 MIMO (also supports RF amplifiers where regulations allow)
· Mesh Networking / Master/multiple slaves / Relay modes
· Auxiliary power output: 12V@ up to 3A (Some other output voltages may be factory configurable in the range of 6-20V)
· Three ethernet interfaces (LANx2 / WAN / bridged) These can act in a bridged configuration (switch), or as independently configurable IP segments
· Dual TTL Serial ports
· USB Slave (switchable), ethernet RNDIS/serial over USB
· User SAMx51 (Arduino IDE) Application processor capable of Ethernet / Serial / CAN / SBUS (other functions like camera control / additional ethernet to serial interfaces possible)
· SBUS In / SBUS Out
· Temperature Monitoring*
· Fan Control
· Status LEDs (Power, Tx,Rx, LAN(2),WAN,RSSI x3, RGB)
· Pixhawk Compatible
· Compatible with our Picoraptor HD Encoder Series
*Function available soon.
NDAA Compliant
Wide range power input: 5-58V
· Up to 1W COFDM RF output, 2×2 MIMO (also supports RF amplifiers where regulations allow)
· Mesh Networking / Relay modes
· Auxiliary power output: 12V@ up to 3A (Some other output voltages may be factory configurable in the range of 6-20V)
· Three ethernet interfaces (LANx2 / WAN / bridged) These can act in a bridged configuration (switch), or as independently configurable IP segments
· Dual TTL Serial ports
· USB Slave (switchable), ethernet RNDIS/serial over USB
· User SAMx51 (Arduino IDE) Application processor capable of Ethernet / Serial / CAN / SBUS (other functions like camera control / additional ethernet to serial interfaces possible)
· SBUS In / SBUS Out
· Temperature Monitoring*
· Fan Control
· Status LEDs (Power, Tx,Rx, LAN(2),WAN,RSSI x3, RGB)
· Pixhawk Compatible
· Compatible with our Picoraptor / PicoNV HD Encoder Series
*Function available soon.
We can also supply high performance antenna solutions (omni / high gain untracked / tracking antennas / RF amplifiers)
To see available variants and to purchase, please visit our online store by clicking ‘shop’ at the top of the page, or click here. Please get in touch if you don’t see what you need.
